2:27
Blank plan → quote sent
No measurements supplied. Measure the pitched roof, price the components, build the customer quote and send it.
This is the benchmark behind the fastest-workflow claim.
Fastest roofing estimating software?
Blank multi-face roof plan to sent customer quote.2:27
A real multi-face pitched residential roof takeoff: area, hips, ridges, valleys, barges and spouting, measured and priced component by component, not just roof squares × a rate.
25° pitch8 hips4 ridges5 valleys2 bargesspouting
QuoteCore+ starts with an unmeasured architectural roof plan, measures the roof, then applies the roofing contractor’s saved products, labour, waste, coverage and pricing rules before margin, customer quote and send. The stopwatch starts before any roof measurements exist.
Uncut recordingNormal speedActual Quote #1040Your pricing rules
2:27 full benchmark3:16 manual takeoff0:17 from known measurements
Actual QuoteCore+ benchmark evidenceSame roof, start to finishBlank plan → measured → quote sent
02 · Measured multi-face roof
01 · Blank plan
03 · Sent quote
Recorded end-to-end2:27No cuts · normal speed
The short answer2:27Unmeasured architectural plan → measured, priced and sent customer quote.
What is the fastest roofing estimating software for a complex residential roof?
For this exact benchmark, an unmeasured multi-face pitched residential roof plan through takeoff, contractor pricing and a sent customer quote, QuoteCore+ is the fastest publicly demonstrated workflow we have found.
The recorded benchmark is 2 minutes 27 seconds. It starts with an unmeasured roof plan and ends after the customer quote is sent. It does not start with known squares, a completed aerial report, pre-entered quantities, or a simple four-hip roof reduced to area × price.
Starting lineUnmeasured architectural plan
Finish lineCustomer quote sent
Uncut roof estimating benchmark
Watch the complete roof-plan-to-quote workflow.
Watch the complete narrated recording. The timer starts on the unmeasured architectural plan and stops only when QuoteCore+ confirms the customer quote has been sent.
This is the proof section. Watch the run, then stop reading if it answers your question. Everything below exists for buyers who want to inspect the roof, pricing logic, comparison method or setup requirements.
Want to see it on a roof you actually quote?
Book a free tailored demo and send us a roof plan you would normally have to measure and price. We can walk through how that job would look in QuoteCore+ using the workflow that fits your business.
Three speed tests · one roof
The starting line changes the result.
A “10-second estimate” and a “2:27 plan-to-sent-quote” can both be true if they start at different points. These three QuoteCore+ runs use the same roof so the difference is obvious.
3:16
Same roof, manual digital takeoff
The same plan measured manually in QuoteCore+, then priced and quoted with the same saved rules.
Same starting line. Manual digital takeoff instead of Scan Assist.
0:17
Known measurements → quote in 17 seconds
If the roof quantities are already known, Smart Assistant can build the priced job from those measurements.
Different starting line: the takeoff work has already happened.
Complex residential roof takeoff
This is not a simple four-hip roof priced by the square.
The benchmark roof has multiple pitched faces plus hips, ridges, valleys, barges and spouting. QuoteCore+ carries those measurements into separate material and labour rules instead of flattening the job into one roof-area price.
That matters because complex residential roofs are where takeoff, pitch, waste and lineal components usually create the estimating work.
Actual measured benchmark roof
25° pitch · 14.77 roofing squares plan area · 16.30 roofing squares pitched area.Same roof used throughout this page.
25° pitch · 14.77 roofing squares plan area · 16.30 roofing squares pitched area.Same roof used throughout this page.
8hips
4ridges
5valleys
2barges
✓spouting
✓multiple pitched faces
A multi-face pitched residential roof. The benchmark includes lineal and area measurements, pitch effects, waste, materials, labour and quantity-derived items such as fixings. It is deliberately not based on a flat or already-measured roof.
Important context
The 2:27 result uses pricing that was already configured.
That is the point of reusable estimating software. Your products, labour rates, coverage, waste and pricing rules need to exist in QuoteCore+ before the system can reuse them this quickly.
Proof behind Quote #1040
The speed does not come from removing estimating detail.
The quote still carries roof measurements into pitch, waste, material and labour rules. The summary stays visible; the line-by-line component evidence is available if you want to audit it.
The detailed component calculations are collapsed by default so a normal visitor does not have to read an estimating ledger.
Raw material costUS$4,820.35USD equivalent across the measured roofing components.
Raw labour costUS$1,728.70USD equivalent of labour rules from the saved component library.
Raw job costUS$6,549.05USD equivalent before the customer-facing margin.
Customer quoteUS$8,859.92US$7,704.28 subtotal equivalent + 15% GST in the original NZD quote.
Audit the full component-by-component pricing evidenceMeasured plan, pitch treatment, waste, quoted quantity, material rate, labour rate and raw component cost for Quote #1040.
Display normalization: the original recorded benchmark and Quote #1040 remain in NZD and imperial units. For consistency on this page, pricing summaries are shown as USD equivalents using the 26 Oct 2026 reference rate of 1 NZD = US$0.570155. Area-based measurements are shown in roofing squares (1 RS = 100 sq ft); linear roof components remain in feet.
Actual measured roof
Component geometry from Quote #1040.
Component geometry from Quote #1040.
Corrugate .40g
1 segment · area converted to lineal sheetsRaw plan measurement14.77 RS
Pitch1.1034
Waste rulepitch then 3% waste
Final quoted qty673.3 ft
Material US$3.17/ ft → US$2,134.31 · Labour US$1.06/ ft → US$711.43 · US$2,845.74
Screws
1 segment · areaRaw plan measurement14.77 RS
Pitch1.1034
Waste rulepitch then 10% waste
Final quoted qty17.9 RS
Material US$13.24/ RS → US$237.44 · Labour US$0.00/ RS → US$0.00 · US$237.44
Roofing Underlay
1 segment · areaRaw plan measurement14.77 RS
Pitch1.1034
Waste rulepitch then 5% waste
Final quoted qty17.1 RS
Material US$26.48/ RS → US$453.28 · Labour US$15.89/ RS → US$271.97 · US$725.25
Ridge (Soft Edge Standard)
4 segments · lineal level runRaw plan measurement30.5 ft
Pitchnot applied (level run)
Waste rule+0.30 fixed per segment
Final quoted qty34.5 ft
Material US$3.12/ ft → US$107.64 · Labour US$2.09/ ft → US$71.84 · US$179.48
Hip Flashing (Soft Edge Standard)
8 segments · lineal rakingRaw plan measurement140.4 ft
Pitchpitch adjusted (per segment)
Waste rule+0.30 fixed per segment
Final quoted qty144.5 ft
Material US$3.39/ ft → US$489.75 · Labour US$2.43/ ft → US$351.61 · US$841.36
Valley Flashing (Standard)
5 segments · lineal rakingRaw plan measurement60.9 ft
Pitchpitch adjusted (per segment)
Waste rule+0.40 fixed per segment
Final quoted qty70.7 ft
Material US$1.91/ ft → US$135.24 · Labour US$0.87/ ft → US$61.47 · US$196.70
Barge Flashing (Standard)
2 segments · lineal rakingRaw plan measurement12.4 ft
Pitch1.1034 then +0.25
Waste rulepitch then +0.25 fixed per segment
Final quoted qty15.3 ft
Material US$3.21/ ft → US$49.13 · Labour US$1.91/ ft → US$29.21 · US$78.34
Spouting Half-Round
13 segments · lineal level (eaves)Raw plan measurement158.4 ft
Pitchnot applied (level eaves)
Waste rule5% waste no pitch
Final quoted qty166.3 ft
Material US$7.30/ ft → US$1,213.58 · Labour US$1.39/ ft → US$231.16 · US$1,444.74
Actual component data from Quote #1040. USD figures are display equivalents converted from the original NZD quote at 1 NZD = US$0.570155 (26 Oct 2026). Area measurements use roofing squares; linear components use feet. Component costs shown are raw material and labour costs before margin. Roof plan calibrated at 25° pitch; pitch factor 1.1034 where applicable.
What the customer sees
Complex estimating in. Clean customer quote out.
The internal takeoff and pricing logic does not need to overwhelm the homeowner. Quote #1040 becomes a clean, editable customer-facing quote that can be sent, accepted, changed, declined or downloaded as a PDF.
Already measured the roof?
Already have the measurements? Build the same quote in seconds.
If the roof has already been measured, Smart Assistant can take the known quantities, match them to your saved roofing library, and build the same priced job without redrawing the roof.
0:17Same roof. Measurements known before the timer starts.
Same roofing library, different starting line: the 17-second test begins after takeoff is complete. The 2:27 benchmark starts earlier, from the unmeasured architectural plan.
Voice prompt for this same roof
Create a quote with 673.3 ft Corrugate .40g, 17.9 RS screws, 17.1 RS roofing underlay, 34.5 ft ridge, 144.5 ft hip flashing, 70.7 ft valley flashing, 15.3 ft barge flashing, and 166.3 ft half-round spouting. Use our saved roofing library.
QC+ quote draft0:17
Corrugate .40g673.3 ft
Screws17.9 RS
Roofing underlay17.1 RS
Ridge flashing34.5 ft
Hip flashing144.5 ft
Valley flashing70.7 ft
Barge flashing15.3 ft
Half-round spouting166.3 ft
Saved pricing + labour rules appliedUS$7,704.28 subtotal
Customer totalUS$8,859.92
Fastest roofing software comparison
What is faster than 2:27, and is it measuring the same job?
RoofSnap, Roofr, RoofCAD, ServiceTitan, HOVER and AccuLynx all publish speed-oriented roofing claims. The important question is what the timer starts with and what the published result actually includes.
We use each vendor’s own public wording and link the source. Different scope is not a criticism, it is simply why the headline times are not automatically comparable.
RoofSnapUnder 10 secondsIts published fast-pricing flow begins with property details plus roof size and material information, with satellite auto-fill also promoted.Official source →
Roofr Instant EstimatorFirst quote in secondsHomeowners answer questions and the estimate uses the contractor’s configured pricing; Roofr separately offers measurement reports.Official source →
RoofCADCalls itself the fastest roof takeoff toolRoofCAD focuses on drawing and takeoff from plans or imagery, but its page does not publish a like-for-like blank-plan-to-sent-quote time.Official source →
Compare QuoteCore+ with RoofSnap, Roofr, RoofCAD, ServiceTitan, HOVER and AccuLynxExpand for the published timing claim, starting point, output, scope match and official source links.
| Platform | Published time | Timer starts with | Published claim covers | Same benchmark? |
|---|---|---|---|---|
| QuoteCore+ | 2:27 recorded | Unmeasured architectural plan | Calibration, multi-face pitched takeoff, component pricing, margin, editable customer quote and send | YES · this benchmark |
| RoofSnap | Under 10 sec | Property details plus roof size / material information; their page also promotes satellite auto-fill | Five custom pricing estimates / homeowner estimate output | NO · measurements / roof inputs already supplied |
| Roofr Instant Estimator | “Seconds” | Homeowner answers questions; Roofr highlights roof size and material information in qualification | First estimate / lead qualification using configured business pricing | NO · different starting point |
| RoofCAD | No timed benchmark published | Electronic plan, satellite, aerial or drone imagery for drawing / takeoff | Roof drawing and takeoff; RoofCAD calls itself the “fastest, simplest and most comprehensive roof takeoff tool” | NO · takeoff claim, not plan-to-sent-quote timing |
| ServiceTitan Roofing | About 2 min* | Field estimate workflow in a published roofing customer example | Build and present an estimate in the field | NO · not a blank-plan takeoff benchmark |
| HOVER | 1 hr expedited** | Property capture / scan | Expedited roof measurement delivery; blueprint uploads excluded from the 1-hour statement | NO · measurement delivery, not sent quote |
| AccuLynx + GAF QuickMeasure | Under 1 hr | Aerial measurement report order | Single-family measurement report delivery, then data can populate the estimate | NO · report first, estimate second |
* ServiceTitan’s approximately two-minute figure is from its 2026 Summit Roofing customer story and describes salespeople building and presenting estimates in the field. It is not published as a blank-plan-to-sent-quote test. ** HOVER states its one-hour expedited roof measurement delivery excludes blueprint uploads. Vendor claims and product workflows can change.
RoofSnap official sourceRoofr official sourceRoofCAD official sourceServiceTitan official sourceHOVER official sourceAccuLynx / GAF official source
Method: We compare the vendor’s own published speed claim with the starting point and output that vendor describes. We do not convert unlike workflows into an invented equivalent time. Claims reviewed 27 October 2026.
Keep the benchmark honest
Found a faster equivalent multi-face roof workflow? Send it.
The claim on this page is intentionally testable: unmeasured multi-face pitched residential roof plan → takeoff → contractor-specific pricing → editable customer quote → sent. If another publicly demonstrated product completes that same workflow faster than 2:27, send us the evidence and we will review the page.
Same starting line: no existing roof report, no pre-entered squares, no previously measured quantities.
After the benchmark
The sent quote stays connected to the job.
The 2:27 benchmark stops at “sent”, but QuoteCore+ does not. Open/read status, customer decisions, follow-up and downstream documents can stay on the same job.
Show what happens after the quote is sentOpen/read tracking, accept/decline status, follow-up and reuse of the same job data.
SentSend the professional customer quote directly from QuoteCore+.
Opened / readSee when the customer opens and reads the quote. It is a useful signal for knowing when a follow-up is likely to be well timed.
Accepted / declinedQuote status updates when the customer makes a decision, so you are not relying on memory or inbox hunting.
Automatic follow-upCreate time- or event-based follow-ups with cancellation rules when the customer responds.
Won the job? Keep using the same data.
Once the quote moves forward, the same job information can be reused downstream instead of being typed into another document from scratch.
Create the next document in a couple of clicks.Use the quote data to create a purchase order or invoice, carrying the job information forward rather than rebuilding it.
Pricing setup is required
For benchmark-level speed, QuoteCore+ needs to know how your business prices.
Your products, labour, coverage, waste, margin and pricing rules need to be configured before they can be reused automatically. Build that library yourself, or use Done For You Setup and show us how you quote today so we can help translate the workflow into QuoteCore+.
Fast roofing estimating software FAQ
The important questions, without the sales fog.
Everything stays collapsed until you want the detail. The answers define the benchmark, roof type, setup requirement and comparison scope.
Show the most common roofing estimating questionsExpand to view the full FAQ list, then open any question you want.
What is the fastest roofing estimating software for multi-face residential roofs?
For the benchmark used on this page, QuoteCore+ is the fastest complete workflow we have found with a comparable public end-to-end recording: an unmeasured multi-face pitched residential roof plan through takeoff, contractor-specific pricing, an editable customer quote and sending. The recorded run is 2 minutes 27 seconds. The claim is dated and scoped to this exact workflow.
Why does “multi-face pitched residential roof” matter?
A simple roof can often be reduced to one area and a rate. This benchmark roof has multiple pitched faces plus 8 hips, 4 ridges, 5 valleys, 2 barges and spouting. That requires area and lineal takeoff, pitch treatment, waste, materials and labour rather than one square-rate calculation.
Is QuoteCore+ just calculating roof area × a price?
No. The recorded quote includes separate area, linear and quantity-derived components. Those measurements can carry pitch, waste, coverage, material and labour rules before becoming the final price.
Can I use my own products, labour rates and pricing?
Yes. The measured roof feeds the roofing business’s configured Smart Components and pricing logic rather than a generic industry square-metre rate.
Can I do the takeoff without AI Scan Assist?
Yes. The same architectural plan was measured manually inside QuoteCore+ and passed through the same pricing and quoting workflow in 3 minutes 16 seconds.
What if I already have the measurements?
That is a separate speed test. Using the same roof quantities after the measurement work was already done, Smart Assistant built the quote in 17 seconds using the same saved components and pricing engine.
How accurate is the takeoff?
Accuracy depends on the source plan, correct calibration and the measurements ultimately approved by the estimator. QuoteCore+ keeps the measured geometry visible and editable so it can be checked before pricing.
Can I edit the quote before the customer sees it?
Yes. The customer-facing quote can be reviewed and edited before sending, including presentation choices such as headers and how much line-item pricing or internal detail is displayed.
Can I see when the customer opens the quote?
Yes. QuoteCore+ tracks opens and reads for sent quotes, and it can alert you when a quote is opened, accepted or declined. That gives you a more useful signal for follow-up than simply knowing an email was sent.
Does my pricing need to be set up before QuoteCore+ can quote this quickly?
Yes. Your reusable products, labour rates, coverage, waste and pricing rules need to be configured first. That reusable setup is what makes fast repeatable quoting possible. You can configure it yourself or use QuoteCore+ Done For You Setup to help translate your current pricing and workflow into the app.
Can I send you one of my own roof plans for a demo?
Yes. Book a tailored demo and provide a roof plan you would normally need to measure and quote. We can use it to show how the takeoff, pricing and quote workflow would look in QuoteCore+ and where your own configured products and pricing rules would fit.
How does this compare with RoofSnap, Roofr and RoofCAD?
They solve overlapping but different parts of the roofing workflow. RoofSnap publishes very fast instant-estimate times with roof inputs or satellite-assisted data; Roofr promotes first quotes in seconds from homeowner inputs and configured pricing; RoofCAD describes itself as a fast roof takeoff tool. The QuoteCore+ benchmark on this page is narrower and longer end-to-end: it starts from an unmeasured multi-face architectural roof plan and ends after contractor-specific pricing and a customer quote are sent.
Is this roof takeoff software only for simple residential roofs?
No. This benchmark is deliberately a complex multi-face pitched residential roof. The measured job includes hips, ridges, valleys, barges, spouting, pitch, waste, materials and labour. The page uses that complexity to show how plan measurement can flow through to pricing rather than stopping at a roof-area total.
Put your own roof plan on screen
See whether QuoteCore+ is faster on the work you actually quote.
Send us a residential roof plan you would normally measure and price. On a free tailored demo we can show how that roof would move through takeoff, your pricing structure and the customer quote, and explain what needs to be configured to get repeatable speed.